How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with a keyless entry system built into. The key functions like an remote control and is exchangeable by a Kia dealer.

Key fobs might stop working for several reasons, including an empty coin battery worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions on how you can get your 2011 kia soul replacement key Sportage replacement key back to working.

How do you replace the remote key or smartkey

No matter if your Kia comes with an intelligent key, remote key push-to-start keys, or regular metal non-transponder key The battery inside these keys will eventually need replacing. This is especially relevant if your vehicle displays a message indicating that the remote or smart keys aren't powered.

This is a relatively simple procedure. To replace the battery of the keyfob remove the mechanical key from the slit on the back of the fob. Then, push the cover open. Inside the key fob, there will be a small screw that holds the battery in place. Remove the old battery by removing the screw using a small screwdriver. Insert the new battery and close the cut on the key fob.

Once the key fob has an updated battery, test it by pressing the locks and unlock buttons. If the doors lock and unlock exactly as you expect, then you're all set! You can now utilize your kia picanto replacement key fob's hands-free lock/unlock feature whenever your fingers feel cold or you need to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a particular programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys) are not required for programming. If your key needs to be programmed, you will need to be aware of the number written on the key code tag and record it in a safe place.

how to start kia replacement key sorento without key fob (Recommended Reading) to replace a battery

If the Kia key fob is unable to respond when you press the lock/unlock button, it is likely that the battery is depleted. A low battery can also cause other issues, such as the check engine light coming on or the engine not running properly. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires only a few tools.

Make sure you turn off your vehicle and shut all doors before you begin. Find the small metal or a plastic piece at the bottom of the key fob. Move it until the metal key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, remove the rear cover and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then orient the replacement battery to ensure that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After you have installed the new battery and turning the key fob off and on in the ignition until the door locks cycle. You can then test your Kia key fob to check if it is working properly again.

How to replace a smart key

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs are equipped with batteries that eventually require replacement. Luckily, this is an easy process that takes only two minutes.

Be sure to switch off your Kia and stand on a flat and well-lit surface prior to you begin. Remember that the fob has small parts that can fall if you're not careful.

The first step is to locate the small release button that is located on the lower backside of your fob. This will either be an oval silver button or a rectangular slot. Once you press this mechanical key blade, it will come out and you can then open the key fob.

Once you have the key fob open it is easy to take off the old battery and replace it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. Once you're done with the battery, you should be able to lock, unlock and start your car using your key fob even if the engine isn't running!

How to replace a mechanical key

The Kia keyfob can be a fantastic convenience, allowing us to lock or unlock our car by pressing the button. Like any other device, it can have problems occasionally. There are solutions to resolve these issues and keep your key fobs in good working order for the duration of.

One of the most frequently encountered problems is a weak or dead battery. This can cause the device to cease working or even to stop working intermittently. If this happens, try replacing the battery with a new one.

If this does not solve the issue, try using an ordinary screwdriver with a flat head to wedge the plastic casing of the fob open. Be sure not to damage any internal components or scratch the plastic. Once the battery is removed, replace it with a new one.

When the new battery is in, close and then open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to ensure that it's working correctly. Contact a dealer, or a locksmith to resolve the problem in the event that the key fob is not working. Make sure they make you an emergency key that works across all trunk and door cylinders in order to prevent lockouts in the future.