Choosing Upvc Window Replacement Hinges

Choosing and fitting upvc window hinges for replacement isn't as difficult as you may think. Make sure the hinges' arrows face the right way and determine the thickness of the hinge arms on the frame that opens (13mm or 17mm).

There are many different types of hinges to choose from, each with unique characteristics. This article will go over the most popular uPVC hinges, and their benefits.

Egress/Easy Clean Hinge

These windows are an excellent choice for replacing or upgrading your fire escape safety windows since they open up to a full 90 degree angle. They can also be removed to an easy clean position to allow you to easily reach the outside of your windows to clean them without climbing on a ladder or lean over at potentially hazardous angles.

These heavy-duty egress hinges are made by Yale one of the most popular and trusted home security brands on the market today. These hinges can be used with any type of uPVC side hung window. They can be moved into the easy-to-clean position by pressing in a small button and then moving the window sash to one side. When the sash is closed, it will be reset to its initial position.

Both 13mm and 17mm are available. Utilize our Egress Selection Guide to help you select the best product for your window.

These hinges are compatible with traditional side-hung frames made from aluminum or uPVC. The friction screw is used to adjust the resistance. This makes it easier to open the window and reduces the possibility of a mishap during high winds. They have been tested for more than 30000 cycles and are in compliance with British Standards approved BS EN 130126-6:2008 and BBA/Secured by Design.

There are no buttons or catches There are no buttons or catches. Nico Egress Easy Clean Friction Hinge is simple to use and provides a convenient solution for emergency egress and safe cleaning. Press the hinge retention clip located on the inside of the bottom corner. This will release both the catches on the top and bottom allowing you move the sash towards the clean position. Once it is in the easy-clean position, close the window to return the hinges to their egress positions.

Fire-Escape Hinge

Fire Escape Hinges, often known as "Easy Clean" hinges are used to replace window hinges side-opening windows to allow escape (fire safety) reasons. They allow for a larger opening in the event of a fire. The building regulations state that this type of hinge must be installed in any habitable space with windows.

The windows feature the benefit of a friction stop that allows them to open to 90 degrees. They also allow the opening sash to slide across the glass when it is opened and allows for easy cleaning without having to climb ladders. The hinges are simple to operate and don't have complicated buttons or catches. They can be operated from the inside of the house with an easy, safe lever.

The hinges are made in the UK by Cotswold and come with a child safety limiter for use throughout the day which can be turned off with a hidden button, providing you with peace of mind that your children won't accidentally open the window too far. The stack heights are 13mm or 17mm.

Take a measurement of the length of the existing side-hung window hinge, which is fixed to the frame. (See the article on measuring the size of buy upvc window hinges window hinges). Then, select the appropriate size hinge from the selections below.

It is important to note that this measurement is taken at the part of the hinge that attaches to the frame and not the sash. The actual hinge length can be longer or shorter dependent on how the windows were made in the past. Also, when choosing the width of your hinge the majority of upvc windows can be fitted with a 13mm stack height. However, should your window frame have 17mm then choose the option to use this. Alternately, you can install the 4mm packer to make up the difference. All hinges are in two different directions (1 left and one right). Screws aren't included with the hinges. They can be purchased separately if you require. We recommend using our Upvc window hinge repair screws. These screws are designed to enhance your hinges' performance and allow them work efficiently for a longer. They have a reduced-friction design and a heightened weather seal that includes an encapsulated nylon reducer cap.

Restricted Hinge

There are occasions when windows must open fully and this can be a problem using the standard hinge. The restricted child safety friction hinges can help overcome this issue and provide a solution when ventilation is needed but access to clean up or escape in case of fire isn't possible. They work by restricting the amount the sash can open and allow the override of this restriction with a button. They work with both top and side hung windows and are available in 13mm and 17mm stack heights.

The Nico Restricted Egress Friction Hinges blend the features of both a standard restrictor and an escape pivot to offer a simple and efficient method of complying with building regulations. It is suitable for side-hung and top opening uPVC windows and is available in 13mm and 17mm stack heights. It is supplied as a pair of hinges where one hinge is the restricted egress, the other unrestricted allowing one of these to be fitted at the lower part of the sash, while the other hinge is installed to the top.

These upvc window hinge adjustment restricting hinges have been tested to BS6375, part 2. They are intended for use on a window that cannot be opened fully like a small children's bedroom. The mechanism restricts the distance the sash opens up to a safe position of 100mm and then re-engages when the window is closed.

These changing upvc window hinges hinges with friction can be used with any type of windows. They are especially useful for windows that are hard to reach, such as those in three-storey apartments or those which would require the use of a ladder. They can be improved with our range security features, including hinge guard protection plate or dog bolts, in order to achieve PAS 24 performance.

When replacing a window hinge, it is essential to determine the length of the existing hinge to ensure that you purchase replacements that are similar in size. This can be accomplished by looking through the image gallery of the hinge before deciding the best place to put it. The hinges that hang from the top can only be placed on one side, while the side hung ones can only be positioned on one side.

Standard Hinge

A standard hinge uses metal-to-metal contacts and has no additional components to reduce friction. It is available in many finishes and also has a fire rating. To quickly determine the radius of a hinge, lay it out flat and align a quarter and dime in two corners. If the quarter is more snug, then the corner should be rounded to 5/8 inches.

Choosing the right type of hinge can determine the success or failure of your door's appearance. Matching the style and finish of your hinges with your door will give it an attractive and well-integrated design.