How to Programming a Subaru Key Fob at Home

You may need the key fob to be programmed by an automotive locksmith or Subaru dealer, based on how old your Subaru is. This is typically accomplished by connecting a computer to the car's computer.

To program your Subaru, unlock the driver's side door using the door button, and then close it. You will hear the chime and see the dome lights flash in the instrument panel.

Step 1: Find the circuit board for your transmitter

There are various ways to program your key fob. First, you must be aware of what kind of key fob you have. You can do this by looking at the shape of your key fob or by listening to the car's chime.

Once you have the information then you can begin the process of programming your keyfob home. You'll require an flathead and a steel key for this. The key fob can be opened by twisting. Push the key's metal part into the case and let go of the battery by pressing the tabs holding it in place. Replace the battery with a fresh one, and then put the key fob case back together.

Step 2: Disconnect the key fob case

Changing the battery is a good idea, as it could revive key fobs that aren't functioning for a while. However, there are some situations where the buttons on the key fob could be damaged. If you notice that the buttons' contacts made of metal have been damaged then you can try soldering them back in place in order to make them function again.

Be sure to turn off your ignition and close your doors prior to you begin. You can accomplish this by closing the driver's door, and then pressing the door button ten times in quick succession. Then, you'll hear the instrument panel chime and your dome lights should flash. This indicates that you're ready to move on.

Step 3: Insert the fob of the key into the ignition

A lot of articles on the internet will show you how to program your brand new or replacement subaru impreza keys keyfob at home. However, the majority of them do not give very specific instructions. Reprogramming an electronic lock is best done by an expert auto dealer in Fort Bliss or a locksmith.

Sit in the driver's seat of your Subaru with the engine turned off and the doors closed. You can open the door button control and use it to unlock all doors. Open and close the driver's doors two more times. Then, remove the key from the ignition switch (don't turn it) 10 times within 40 seconds. The system should sound chirps to confirm that the settings have been altered.

Step 4: Turn the Ignition On.

It is important to know that this method of programming a key fob is effective if you have a working key. If you don't then a dealership or auto locksmith will be required to program a new key for your subaru replacement key fob in Fort Bliss.

After the key is programmed, it should be capable of starting your car in about 5 minutes. To begin, make sure all doors are shut and the engine is off. Assume a seat in the driver's chair and unlock all the doors using the door button. Insert the key into the ignition, turn it on to the off position (the electrical systems will come on, but the engine will remain off), and then back to the off position ten times in quick succession.

Step 5: Unlock the Driver's Door

Subaru offers many high-end automobiles equipped with key fobs that lock and unlock doors, start the engine, and even defrost windows. These devices can stop working.

To fix the issue then you should contact an auto locksmith or dealer. This will solve the issue and ensure that your car is safe.

To accomplish this, you need to open the door to the driver's side and close it. Then, insert the ignition key in and turn it to the first position. Then, you can turn it back to the off position. Perform this as fast as you can ten times. After ten times you will hear a chime.

Step 6: Press the Lock/Unlock Button on the Driver's Door

The procedure for replacing the battery on a subaru flip key remote key (website) fob is very simple. Unlock the exterior fob case. Then you can use an flathead screwdriver, to pry open the inside of the case and take out the old battery.

After removing the battery and replacing it with the new one. Close the case. Then, you can sit in the driver's seat, and unlock all the doors using the door button control. Finally, place the ignition key and turn it so that the electrical systems are switched on but the engine is off. Repeat this ten times until you hear the chime on the instrument panel. This will turn the system into programming mode.

Step 7 Step 7: Press the Lock/Unlock button on the Passenger's Door

For certain owners, the irritating noise that occurs when locking and unlocking the Subaru key fob from outside the vehicle can be distracting. In certain situations, the chirp can be turned off by opening and closing all doors and a double-click of the lock button on the key fob.

Close all doors, including the fuel-filler lid, and turn off the ignition. Press and hold the lock side of the key fob's lock button for 10 seconds. After this is done the instrument panel emits an audible chime. The chime signals that the fuel-filler lid and door are locked. The setting can also be changed to make the doors and lids of the fuel-filler are locked automatically without pressing the request switch.

Step 8: Enter the 8-Digit Transmission Number.

Remember the first 8 digits in your head. Then, sit in the driver's seat, shut the doors and turn the key to the first position. After ten turns, the instrument panel should sound once.

Next, open the case for the key fob and look for the circuit board that controls the transmitter. There should be two or three sets of numbers (8-digits) on the circuit board. Follow the steps in the guide to register the code. For older models, this procedure might require a visit to the dealer.