How to Replace a Kia Sportage replacement key fob Kia Key

For a variety of kia sorento key fob models the key comes with a built-in keyless entry system. This key usually resembles a remote control and can be replaced with a fresh one from a Kia dealer or locksmith.

Key fobs might stop working for several reasons, including batteries that are dead, worn buttons or buttons, water damage, signal interference and a malfunctioning receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work again.

How do you replace the remote key or smartkey

The battery inside your 2013 kia optima key fob's smart key will eventually have to be replaced, regardless of whether it is a remote key or a push-to-start one, or a normal metal key that doesn't contain an electronic transponder. This is particularly when the car displays a message that the smart key or remote has a low battery.

Luckily, this is an easy procedure. To replace the battery in the key fob, remove the mechanical key from the slit in the back of the key fob. Next, lift the cover. A small screw will be in the key fob to keep the battery in place. Using a small screwdriver, take the screw off and remove the old battery. Then, insert the new one and close the slit inside the key fob.

When the key fob is equipped with a fresh battery, test it by pressing the lock and unlock buttons. It's good if the doors lock and unlock as you expect. You can now make use of the hands-free lock/unlock feature on your Kia when your fingers are cold or you need to make errands in Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a programming machine that is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys) are not required for programming. If your key requires to be programmed again, you must know the key code number printed on the tag of the key code and save it in a safe place.

How do you replace a battery?

If your kia ignition key replacement key fob isn't responding when you press the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A weak battery could cause other issues, such as the check engine light appearing or the engine not working properly. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires just the most basic tools.

Before you begin the process ensure that your vehicle is off and that all doors are shut. Locate the small plastic piece that is on the bottom of your key fob and move it until a metal key slides out. Then, you can put the key into the door handle of the driver to unlock your car.

To replace the key fob battery, remove the rear cover and use a plier bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then align the new one to ensure that the "+" positive side is facing you, and the "negative" negative side is facing towards the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's Key fob again to make sure it's functioning properly.

How do you replace a keyless key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart key comes with an incredibly small key blade that is hidden inside, while the standard fob does not. Both key fobs come with a battery that will eventually require replacement. It is a simple process that takes less than two minutes.

Before you start before you begin, ensure that you're on a level surface with enough lighting and that your Kia is not on. Keep in mind that there are tiny parts inside the fob that can fall out if not cautious.

The first step is to locate the small release button that is located on the lower backside of your fob. It will be an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery is CR-2032, and can be purchased on the internet or at your local auto parts shop. Once you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do you replace a broken mechanical key

The Kia keyfob is a great convenience which allows us to lock or unlock our car simply by pressing one button. But, as with all devices it may have issues occasionally. Luckily, there are methods to troubleshoot these issues and ensure that our key fobs are in good condition for the long run.

A low or dead battery is among the most frequent problems. This can cause your fob to stop working or work intermittently. If this is the issue you should replace the battery a new one.

If this doesn't solve the problem Try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. After the battery has been removed then replace it with a new one.

When the new battery is installed, close and unlock the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and verify that it's working properly. If the device isn't working, call an expert locksmith or dealer to help solve the problem. Make sure they cut you an emergency key that functions across all trunk and door cylinders to avoid lockouts in the future.