How to Repair Bifold Door Top Roller Guide

If your bifold door is sticking then it's likely that they require some maintenance. They could need to be cleaned, lubricated or adjusted. The issue could be caused by loose screws on the top pivot or by the top roller guide.

This kit includes everything you need to restore your bi fold door repair near me-fold wardrobe door to its peak performance.

Take the door off

Installing an internal set of bifold doors could appear to be a complicated and challenging task, but it's actually quite simple for anyone with a few years of experience. The frame isn't the problem however, getting the doors to close and fold smoothly is. Bifold doors are complex pieces of machinery, and as such they could require some tuning up to keep working correctly. It could be as simple as tightening the screw, or as intricate as taking out and replacing the pivot pin or roller.

It is usually possible to fix these problems with a few simple adjustments, without having to remove the doors. You might notice that your bifold doors are sliding and scraping the floor or slipping off track. In order to fix these issues, it isn't a big deal, and with three easy steps your bifold doors can be back in the blink of an eye.

One of the most common problems that bifold doors with internals have to face is the tendency to slide out of alignment. This could be due loose screws, holes on the anchor/pivots or a misaligned bifold door. The majority of the time this can be fixed by making a few minor adjustments. However, if your door isn't moving at all, you may need to replace it.

To remove the door to open it, you'll require an screwdriver and perhaps pliers (to aid in loosening any pins on the pivot that are stuck). The screwdriver can be used to loosen the locking levers at the bottom bracket for pivots. The pliers are used to take off the pin.

After the top roller is loose it should be possible to lift the door and swivel it down in order to lift it off its pivot brackets and track. It's usually a straightforward procedure, but be careful to not let the door strike the door frame. Then, you'll be able to saw off the edge of the door that's scraping the floor, and sand it down until it's smooth. You can then repaint or refinish it as required.

Remove the Roller Guide

This spring-loaded roller guides the mount on top of bifolding doors to aid in smooth operation. It is designed to work with Kenna frames and will fit the door's panel from 1 to 1/8 inch thick. It is made from steel, nylon and plastic components. It will replace the damaged guide.

Remove any screws that hold the guide to the roller using the screwdriver. After that, carefully use your hands to pull it out of the frame. This may require some effort, so have someone else help you keep the door in place as you take it off.

Once the old guide is removed, carefully cut the remaining finish on the foot of the new guide using a sharp blade to remove it from the rod blank. This will make it easier to remove and ensure that there is no damage to the new guide foot. The foot is extremely sharp and could cut or snag fingers.

You may need to apply some force to remove the guide, but be careful not to break or chip the foot. After you have removed the guide, you must remove any epoxy or threads left in the area it was attached. This will help avoid any future issues with the guide.

After removing the old guide, try out your new guide by putting it in its new location and then applying a few rotations of masking tape or a form of guide tubing to keep it in place. This will allow you to double verify the guide's spacing and alignment to ensure that everything is properly set up. This step is crucial to avoid future problems, whether you use the CRB Spine Finder & Deflection System or simply eyeball it.

If the guide is placed correctly and functioning in the way it should the next step will be to put the door back in place. Remember that any screws or pins that you removed or loosened should be replaced and tightened appropriately after you've finished.

Take the Bottom Pivot off.

Bifold doors can be a beautiful addition to any home, but they may require to be tweaked or adjusted to ensure they are in good working order. While some of the more straightforward issues can be resolved with the doors in place, some will require removal. This guide will guide you through the steps to remove the internal bifold door pivots, pins and rollers to get your doors sliding as new.

Gathering your tools is the first step. Putting everything together ahead of time will help you avoid a lot of frustration later in the process. You'll need a screwdriver, pliers and perhaps a wrench. You can pick up an assortment of basic tools at your local hardware store for a reasonable price. It's recommended to have some wood glue in your kit. This can be very useful if you have to glue one rollers back into their original position.

After putting together your tools, open the bifold door and loosen the top track bracket using your screwdriver. Once this is loose the door should be free to slide off the top track completely. It might take a little shaking to get it there, but it should come off the track.

The pivot on the bottom of the frame needs to be removed. Close all interior doors prior to starting. This will make it much easier rather than working from the inside. If the bottom track still looks good it is possible to raise the door to take off the track.

If the track is damaged, then you'll have to replace it. You can purchase replacement tracks for both bifold doors as well as swinging closet doors from a local hardware store. If the track is severely damaged, you might need to replace it completely.

Now that your track is repaired or replaced it is time to test the doors for the proper operation. Check that they're capable of moving smoothly in and out of position. You'll also want to check that the edges of the door are parallel to the frame when it is closed. If they aren't, then you'll have to adjust the top pivot bracket and tighten or loosen the bottom screwscrew until the door's edge is perfectly aligned with the frame.

Replace the Roller

If they are installed correctly the bifold doors can easily enclose laundry nooks, pantries and closets. They are made up of two panels that are hinged and slide open on a track that sits in the top of the frame. Over time the roller guide bearings can wear out, causing the doors to slide and rub against the floor. Replacing the guide roller takes just a few minutes and a few basic tools.

The first step is to take the roller guide from the door panel. The bolt that holds the bottom pivot must be removed and the screw that holds the guide to the top of the door panel should be loosen. After the guide is removed then lift the door frame up and out of its track. Then, using a wrench, remove the top pivot bolt from the hole in the header of the frame by loosening the nut.

A replacement top nylon roller guide that has a 7/8 inch diameter wheel and a steel base is available from Stanley, Cox or Acme. It is mounted on the top edge of bifold doors that range from 1 to 1-3/8 inches thick. It is spring loaded and adjusts itself in the upper track to ensure smooth gliding.

Another issue with bifold door repair bracket doors is that it scrapes the floor when it is closed or opened. This can occur after installing carpet, or other flooring materials that require the doors be raised slightly to allow for clearance. This issue can be resolved by removing the screws that adjust the bottom pivot and loosening the top track mounting screws and moving anchor/pivot.

A set top roller with new guides could be a low-cost solution to the problem of your bifold door repair near me doors being difficult to operate. They are usually available at the local hardware store in the door section. However, they can also be purchased online from several suppliers. Along with a brand new top roller guide, you will need a small container of Elmer's wood glue, which is available in big box stores as well as a squeeze clamp. The clamp is used to keep the repair bifold door top pivot area tightly closed after the glue has been inserted and allowed to dry.